Stock Status - In stock
Important note for latest batch:
- 50% of people with D2E chipsets and D2E d2pros will have to solder 1 wire manually (the J point). You will require a soldering iron for this
- D2E d2pros don't work as well on d2c2/d2c chipsets. If you let us know what chipset you have (if in Australia just tell us your serial number) we will either flash the best firmware on for you, or provide you with a green stickered d2pro. If you fail to read this, the d2pro will either not work, or be a bit sluggish. To fix this you will need to buy a d2prog programmer.
- These D2pros work on D2B (older wiis) as well. Please let us know if you have these chip as well, as we need to solder the modchip differntly for you.
- In short, just let us know what type of Wii you have so we can make this a smooth transaction!
We ship these all around the world. International shipping starts at $10 for registered post
Some info on the D2pro 9 wire:
D2pro 9wire is the "it" modchip at the moment. The SPI is upgradeable via DVD, and the Actel is upgradeable via JTAG (using the d2prog). D2pro team have proven that they are more then one step ahead of the competition. Their "competitors" are Argon and wasabi. Wasabi has an issue with 5~10% of DVD drives, plus they are not upgradeable via JTAG, just DVD, even though it hasn't been upgraded yet, not even a proof of concept! The guys who wrote Argon copied Wasabi code, and have ported it to their modchip. Probably not the best idea to copy a buggy modchip hey?
D2pro code is original, and they are the ONLY team to have already figured out the new 'd2c2' security chip. Unmoddable wiis? No problem! It only took them 1 week to figure out. So if you have bought a Wii in the US after April the 20th, or in the UK after the 5th of May, or in Australia with a serial above lah1045, place your order, we are ready to go!
The presoldered clips will be shipped in d2c/d2c2/d2e mode. If you have a serial number for a DMS/d2a/d2b/d2b-cutpin wii you MUST tell us in the order comments when checking out, otherwise the modchip will not work on your console!
Firstly a warning:
All Wii-Clips that have D2Pro soldered to them will be tested. OzModChips.com takes no responsibility AT ALL for any damage you or the wii-clip may cause to your wii during installation, 1 week, or 5 years after 'installing the product'.
On to the product!
What is this thing?
The Wii-Clip is not a modchip, it is a solderless interface that can be used on D2C consoles to install the D2Pro 9 wire without wires! Please note that there is 1 point on the d2pro that is usually soldered to onto a pad. Point J. This point passes through a resistor before hitting the IC. We have been testing it out, and every single Wii will work fine, 100% solderless. If it doesn't work on your Wii please be prepared to solder 1 wire. If this is beyond you, then you might want to consider the other d2pro.
D2pro has automatic region detection. We will test these out on a console here, and then wipe the d2pro clean and reinstall the firmware, so that its 100% new when you get it.
Please read the official page in full to understand the product.
Hasn't every single IC-Clip in the past been a horrible failure?
Yeah, pretty much. PS2 ones where terrible. There was a recent Wii one for D2B consoles made by a bunch of Spanish guys. It was terrible....some home made POS.
So what makes this different?
The Wii-Clip is selling pretty cheap, but it is in no way a cheaply made product! The guys that designed it obviously have a very good factory doing this for them. The Wii-Clip hugs the IC so tight that onces its on.....its really on. We think that there is a very small chance that the vibration of the Wii will move the clip as there is no where for it to really move. The Wii-Clip slightly blocks the air flow inside the wii - but with correct installation it shouldn't be a problem.
How do you install it?
What comes inside the packages you offer?
Everything you need! Wii-Clip V4C, D2Pro soldered on + Triwing Screwdriver
Wii-Clip V4C, D2Pro soldered on
Wii-Clip V4C, D2pro sealed + Triwing Screwdriver
Wii-Clip V4C, D2Pro sealed
Wii-Clip V4C
We ship these packages anywhere in the world. International customers can pay via paypal only.
Important information on warranty:
There is nothing better than actually installing a modchip in your wii with wires. Solder is an extremely strong bond, and installers can give warranty on their work, and on the product. We can only provide a DOA (dead on arrival) warranty on these products. If you are experiencing a problem with your wiiclip you must notify us of this within 7 days of receiving the item. We simply cannot provide a long term warranty on a product that is not installed by us. We will test each each pre-soldered solution before sending the item to you, and this does narrow the chances of it not working, however, by buying this product, you are agreeing that there is only a DOA warranty and OzModChips will not accept returns whatsoever after this period.
